Before any oil goes into a machine, the first question on site is almost always the same: can this unit handle my oil directly? The trouble often sits in the word directly. A plate and frame filter press and a vacuum oil purifier remove completely different things: the first holds back solid impurities, the second draws water and gas out of the oil, and the order of the two is not a matter of preference.

Once the division of labour is clear, selection stops being a question of which machine to buy and becomes a question of how many process steps the job needs.

What each of the two steps actually removes

A plate and frame filter press does deep-bed filtration with frames, plates and filter cloth or paper. The LY-200 carries 40 sets of 300×300 frames, handles 4800 L/h and uses an 11 kW motor; the LY-50 carries 10 sets of 200×200 frames with a 4-1.5-b3 motor and a kcb33.3 oil pump. The filtration accuracy of this class of machine sits in the ≤5–20 μm range: it removes sludge, iron particles, oxidation products and part of any emulsion, and the rest of the solids stay on the cloth as filter cake that can be scraped off and disposed of separately.

A vacuum oil purifier does something else. The ZYD-100 handles 6000 L/h at a working vacuum of -0.08 ~ -0.0999 MPa, with a filtration accuracy of ≤1 μm and a cleanliness of NAS 1638 class 5. It heats the oil, atomises it and lets water and dissolved gas escape under negative pressure; the result is a water content of ≤3 ppm (GB/T 7600), a gas content of ≤0.01% (GB/T 423) and a breakdown voltage of ≥65 kV (GB/T 507). It holds back fine particles, but it has no dedicated arrangement for trapping large lumps of solid.

The plate and frame group and the control cabinet of a plate and frame filter press
The chambers of a plate and frame filter press do deep-bed filtration through cloth or paper, and the solids end up there as filter cake that can be scraped off
Process stepTypical machineWhat it removesThe matching indicator
Pre-filtrationJL series cart type oil purifier, filtration accuracy ≤10–25 μmParticles above 20 μmProtects the elements and the pump group behind it
Coarse separationLY-200: 4800 L/h, 40 sets of 300×300 framesSolid impurities and part of the emulsionFiltration accuracy ≤5–20 μm
Dewatering and degassingZYD-100: 6000 L/h, -0.08 ~ -0.0999 MPaWater and dissolved gas≤3 ppm (GB/T 7600), ≤0.01% (GB/T 423)
Deep-bed fine filtrationFine element 150-500-5, 5 of them in parallel on the ZYD-100Fine particles≤1 μm, NAS 1638 class 5
DecolourisationTL series adsorption unitsPigments and odours from oxidation and blackeningDifferential pressure across the activated carbon or silica gel medium

Why the order cannot be reversed

Running the degasser first and the press second sets off three reactions in a chain. First, solids take up the surface of the filter media, so the elements are already climbing in differential pressure before any dewatering or degassing has started; the flow rate falls and the same batch of oil takes longer to process. Second, particles carried into the flash chamber by the negative pressure disturb the atomisation; the oil film cannot be made thin, the water vapourises more slowly, and degassing efficiency depends precisely on that film area. Third, emulsified water is water held inside solid particles and surfactant to begin with; neither gravity separation nor vacuum separation removes it, and a plate and frame press is equally limited with emulsified oil of high water content. That point has to be made clear during selection.

  • The oil is already black and smells burnt: press it first to remove the solids, then decolourise it, with the adsorption unit following the vacuum degasser.
  • The oil only carries water and gas and is still clear: there is no need for a plate and frame press; go straight to the vacuum degassing stage.
  • The oil is very dirty and full of contaminants: use a JL series cart first to hold back particles above 20 μm, then feed the vacuum machine.

When one machine is enough

Not every site needs two machines. A plate and frame filter press earns its place where the oil volume is large, the contamination is heavy, continuous operation over long runs is needed and the filter cake has to be recovered; clarification on a continuous production line fits the centrifugal type better, with the LX-100 at 2400 L/h and the LX-200 at 4800 L/h and a separation accuracy of ≤5 μm; new insulating oil or mildly damp oil needs nothing more than a two-stage vacuum oil purifier. Settle the number of process steps first and the model afterwards, and neither the quotation nor the acceptance test will have to be redone.

ZYD-100 two-stage vacuum oil purifier
The two-stage vacuum oil purifier takes care of the water and the gas; large solid lumps are not its job
A plate and frame filter press and a vacuum degasser are not two alternatives but two consecutive steps: hold back the solids first, then take out the water and the gas. Reverse them and what you gain is differential pressure and time.